Remote Vehicle Control System
SRT 1600
Owner's Manual
Deluxe Vehicle Security and Keyless
Entry System with 900Mhz Two Way
Confirming LCD Remote Control
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this
manual is applicable to most vehicles. However, due to the configuration of some vehicles, some
functionsAND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more
information.
1
Using Your Remote Control
Arming the Security System
To arm the system, exit the vehicle, close all doors, then press the LOCK button on the remote control. The system
will sound 2 times and the parking lights will flash 2 times, indicating the system is armed, has locked the doors (if
equipped and connected) and activated the starter disable feature. The status indicator (blue warning light on the
dash) will blink steadily, once per second. To arm the system silently, press and hold the LOCK button for 1 second.
The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and
connected) and activated the starter disable feature. The status indicator (blue warning light on the dash) will blink
steadily, once per second.
Pre-arm Mode
If the system sounds 1 time and the parking lights flash only 1 time, this indicates that the vehicle’s interior light is
on or an entrance is left open. Check to see that all doors hood and trunk are closed properly. Once all entrances
are secured (and the interior light is off), this system will sound/flash again. The system is now fully armed. (If the
entrance is not secured within 4 minutes, the system will arm and ignore the unsecured entrance until it is closed.)
Disarming the Security System
To disarm the system press the UNLOCK button. The system will sound and the parking lights will flash once, and
the doors will unlock (if equipped and connected). To disarm the system silently, press and hold the UNLOCK
button for 1 second. The parking lights will flash, indicating the system is disarmed and has unlocked the doors (if
equipped and connected).
Disabling/Enabling Confirmation Chirps
1. Turn the ignition key ON then OFF.
2. Within 10 seconds push and release the valet/override button 3 times.
3. The system will sound 2 times to disable confirmation chirps or 1 time to enable confirmation chirps.
Attempted Intrusion Identification
This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion
attempt occurred, the system will sound 4 times and the parking lights will flash 3 times when disarming the system.
Enter the vehicle an observe the dash mounted status LED to Identify which zone was triggered.
1. Shock Sensor - 1 flash, pause 1 flash, etc.
2. Hood or Trunk Pin switch - 2 flashes, pause 2 flashes, etc.
3. Door Entry - 3 flashes, pause 3 flashes, etc.
The intrusion warning indicators are stored in the system’s memory and will be erased when the ignition key is
turned on.
Two Stage Door Unlock (Optional)
If this feature is enabled on your system, pressing the UNLOCK button one time on the remote control will unlock
only the driver’s door. Press UNLOCK again to unlock the remaining doors.
Activating the Trunk Release Feature (Optional)
If this feature is enabled on your system, pressing and holding the TRUNK button on the remote control for 2
seconds will open the vehicle’s trunk or hatch.
*Throughout this manual, ‘press’ refers to pressing for less than 1 second, ‘press and hold’ refers to pressing for
more than 2 seconds.
3
Using Your Remote Control, continued
Turning on the Vehicle’s Headlights (Optional)
If this feature is enabled on your system, pressing and holding the LOCK button on the remote control for 3
seconds will turn on the vehicle’s headlights for 30 seconds.
Activating Optional AUX 1 (Optional)
If this feature is enabled on your system, press and release the OPT button on the remote control to activate an
optional feature. This feature can be programmed for a wide range of functions like power window or sunroof
automation, please consult your installing dealer to determine functionality of your system.
Activating Optional AUX 2 (Optional)
If this feature is enabled on your system, pressing and holding the KEY button on the remote control for 2 seconds
will activate an optional feature. This feature can be programmed for a wide range of functions like power window
or sunroof automation, please consult your installing dealer to determine functionality of your system.
Activating Optional AUX 3 (Optional)
If this feature is enabled on your system, pressing and holding the LOCK button and the Trunk button on the remote
control simultaneously for 2 seconds will activate an optional feature. This feature can be programmed for a wide
range of functions like power window or sunroof automation, please consult your installing dealer to determine
functionality of your system.
Activating Optional AUX 4 (Optional)
If this feature is enabled on your system, pressing and holding the UNLOCK button and the TRUNK button on the
remote control simultaneously for 2 seconds will activate an optional feature. This feature can be programmed for a
wide range of functions like power window or sunroof automation, please consult your installing dealer to determine
functionality of your system.
Using the Progressive Car Finder Feature
Press the LOCK button and the UNLOCK button on the remote control to locate your vehicle. The system will
sound 5 times at low volume increasing in volume each of 3 times the button is pressed.
Using the Personal Protection Alarm (Panic)
Press and hold the LOCK button and the UNLOCK button on the remote control for 2 seconds to activate the
personal protection alarm. The system will sound for 30 seconds. Pressing any button on the remote control will
turn the personal protection alarm off.
Using Valet Mode
To engage valet mode:
1.
2.
3.
Turn the ignition key to the ON position.
Press and hold the emergency override button.
The blue dashboard mounted LED will light solid indicating that the system is in valet mode.
When valet mode is activated the dash mounted status LED will light solid, and all security functions will be
disabled.
To disengage valet mode:
1.
2.
3.
Turn the ignition key to the ON position.
Press and release the emergency override button.
The blue dashboard mounted LED will turn off indicating that the system has exited valet mode.
4
Additional LCD Remote Control Functions
LCD Remote Control Display Illumination
Press and release the “F” button on the LCD remote control one time. The display will illuminate for 10 seconds.
LCD Remote Control Vibrate or Tones
Press and release the “F” button and the UNLOCK button on the LCD remote control simultaneously one time to
toggle between beep tones and vibrate mode. The LCD remote control will either beep or vibrate to indicate which
mode is selected.
Page Call Out
From within the vehicle, press and hold the emergency override button for 4 seconds, the LCD remote control will
emit a beep tone to indicate that someone is calling you to the vehicle.
Out of Range
If the LCD remote control is within operating range of the vehicle the antenna or IN-RANGE INDICATOR icon will
be displayed after any button is pressed. If this icon disappears after a button is pressed the vehicle is out of range
of the remote control.
Countdown Timer
The LCD remote control is equipped with a countdown timer for situations where an alert tone may be needed to
remind you of something important. The countdown timer allows you to set the timer up to 19 hours and 59 minutes.
Refer to page 10 for programming.
Parking Meter Timer
The LCD remote control is equipped with a parking meter timer that allows you to set a countdown timer for 10, 20,
30, 60, 90 or 120 minutes. The LCD remote control will emit a beep tone when the timer expires. Press ”F” and
TRUNK simultaneously to select desired time.
Alarm Clock
The LCD remote control is equipped with a built in alarm clock that can be set to beep at a certain time each day.
The alarm clock must be set, and the feature turned on. Refer to page 10 for programming time. Press ”F” and
KEY simultaneously to turn ON and OFF if the desired time has already been set.
Bypassing The Shock Sensor
There are 3 additional modes of operation in which your system will react to the shock sensor, FULL TRIGGER
ONLY, ALL OFF, or CITY MODE.
Press LOCK once to arm the system.
Pressing LOCK again within 2 seconds will set the system to FULLTRIGGER ONLYin which the system will
ignore the light touch setting.
Pressing LOCK again within 2 seconds will set the system toALL OFF. In this mode the system will not react to the
shock sensor and the 2-way LCD remote will display the shock sensor icon.
Pressing LOCK again within 2 seconds will set the system to CITY MODE. In this mode the light touch horn output
is extended to a full 10 seconds and full trigger horn output is shortened to 15 seconds, no icon is displayed.
NOTE: The system will only change the shock sensor setting for one arm cycle and will be defaulted back to normal
operation the next time the system is armed.
5
Additional LCD Remote Control Functions, cont.
Check Vehicle Status
Press the LOCK, TRUNK and KEY buttons simultaneously for 1 second. The LCD remote control will display the
system’s current status.
Check Temperature
Press the TRUNK and KEY buttons simultaneously for 1 second. The LCD remote control will display the
vehicle’s interior temperature.
Battery Save Mode
Press the LOCK and “F” buttons simultaneously when the system is disarmed. Note that in this mode the remote
will not send or receive vehicle status unless you press a button on the remote.
Temperature Display
Press and release the TRUNK, KEY and “F” buttons simultaneously to change the temperature display between
Fahrenheit or Celsius.
LCD Remote Control Options Menu
Accessing the Options Menu
1. Press and hold the “F” button for 5 seconds.
2. Press the “F” button to select the setting to change.
3. Use the TRUNK or OPT button to change the digits.
4. Press “F” to keep setting and advance to the next item.
5. Press and hold “F” for 5 seconds to exit options menu.
Selectable Features in the Options Menu
1
Time Set - Hours
Time Set - Minutes
Alarm Clock - Hours
Alarm Clock - Minutes
2
3
4
5
Alarm Clock Melody
Alarm Clock - ON / OFF
Countdown Timer - Hours
Countdown Timer - Minutes
6
7
Countdown Timer / Remote Start Shutdown Melody
Countdown Timer - ON / OFF
8
Remote Start Melody
6
Quick Reference Button Operation Guide.
Operation Function
Lock
Unlock
Trunk
KEY
OPT
F
Operation Method
Lock
X
Press and Release
Unlock
X
Press and Release
Headlight
X
Press and Hold for 3 seconds
Press and Hold for 2 seconds
Press and Release
Trunk
X
Car Finder
Panic
X
X
X
X
Press and Hold for 2 seconds
Press two times in 2 seconds
Press and Release
Remote Start
Temp Start
Daily Start
AUX1
X
X
X
X
X
X
Press and Release
X
Press and Release
AUX2
Press and Hold for 2 seconds
Press and Hold for 2 seconds
Press and Hold for 2 seconds
Press both together for 1 second
Press both together for 1 second
Press and Release, When System is Disarmed
Press and Release
AUX3
X
X
X
X
X
X
X
AUX4
X
X
Check Status
Check Temp
Battery Saver
Vibrate
X
X
X
X
2/4 hour start
Shock Bypass
Parking Meter Timer
Alarm clock
Fahrenheit / Celsius
X
Press 4 times after remote start shut down
Press and release 2, 3, or 4 times
Press and release 1, 2, 3, 4, 5 or 6 times
Press and Release
X
X
X
X
X
X
X
X
Press and Release
Replacing Remote Control Batteries
2-way LCD Remote Control:
The AAA alkaline battery inside the 2-way LCD remote control should last approximately 1 year under normal use.
When the battery becomes weak you will notice the remote control range (the distance from the vehicle the remote
control will work) deteriorate and the BATTERYicon on the LCD remote control will display. To replace the remote
control battery:
1.
2.
Lift and slide the battery cover off of the remote control.
Remove the oldAAAbattery, observing the +/- symbols on the battery, and replace with a new
AAAbattery.
3.
4.
Gently slide the battery cover onto the back of the remote control until it locks into place.
Test operation of the remote control.
1-Way 5 Button Remote Control:
The two 3 volt lithium batteries (model CR2032 or Code Alarm part # 6BA) inside each remote control should
last approximately 1 year under normal use. When the batteries become weak you will notice the remote control
range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote
control will dim. To replace the remote control batteries:
1.
2.
3.
Using a small (#1) philips screwdriver, remove the 2 screws on the back of the remote control.
Gently unsnap the halves of the remote control apart.
Slide the lithium batteries out of the circuit board, observing the +/- symbols on the batteries
and replace with new lithium 3 volt batteries (model CR2032 or Code Alarm part # 6BA)
Gently snap the halves of the remote control back together and reinstall the philips screws
on the back of the remote control.
4.
5.
Test operation of the remote control.
7
LCD Screen Icons and their Indications
TRANSMITTING
BATTERY INDICATOR
VALET MODE
IN-RANGE
INDICATOR
P. LIGHT FLASH
SHOCK TRIGGER
HOOD
LOCKED/ARMED
UNLOCKED/DISARMED
SILENT ARM/DISARM
DAILY START
TIMER MODE
DOOR TRIGGER
TEMPERATURE
START MODE
ALARM CLOCK MODE
IGNITION TRIGGER
TRUNK
COUNT DOWN
TIMER MODE
ENGINE RUNNING
CALL
PAGE FROM VEHICLE
VIBRATE/SILENT MODE
REMOTE START INHIBIT
NO START
BATTERY SAVE MODE
CLOCK / TIMER / TEMP. DISPLAY
8
Emergency Override Procedure
If your transmitter is lost or disabled, it will be necessary use the emergency override button to turn the security
system off. There are two types of emergency override procedures. Check with your installing dealer to find out
what has been activated on your system.
Standard Emergency Override Procedure
1.
2.
3.
Enter the vehicle (the security system will trigger).
Turn the ignition key to the ON position.
Press and release the emergency override button (The security system will turn off).
Note: If the automatic arming feature is enabled on your system. The security system will re-arm the next time the
ignition key is turned off and the vehicle’s doors are closed.
Coded Override Procedure
The system has an optional override mode that allows you to program a 2-digit personal code using the
emergency override button offering a higher level of security. This feature must be enabled by your installing
dealer, the default override code is 11.
1.
2.
3.
Enter the vehicle (the security system will trigger).
Turn the ignition switch to the ON position.
Within 5 seconds press the emergency override button the number of times corresponding to
the first digit of your personal code (Default digit is 1).
4.
5.
Within 5 seconds turn the ignition key OFF, then ON.
Within 5 seconds press the emergency override button the number of times corresponding to
the second digit of your personal code (Default digit is 1).
6.
7.
8.
Within 5 seconds turn the ignition key OFF, then ON.
If entered correctly the security system will turn off.
Turn the ignition key to the OFF position.
Programming Your Personal Override Code
1.
2.
3.
4.
Make sure the security system is disarmed.
Turn the ignition key to the ON position.
Within 10 seconds press and release the override button 3 times.
Within 10 seconds turn the ignition key OFF then ON 3 times (The horn will honk and the lights
will flash 1 time).
5.
Within 10 seconds press and release the override button the number of times
corresponding with the first digit of your personal code (1-9).
6.
7.
Within 10 seconds turn the ignition key OFF then ON.
Within 10 seconds press and release the override button the number of times corresponding
with the second digit of you personal code (1-9).
8.
9.
Within 5 seconds turn the ignition key OFF.
You will notice the LED flash a number of times corresponding with the code you entered.
Note: If 15 seconds of inactivity passes the system will abort programming.
Note: Do not lose your “Personal Override Code”. Reprogramming a new code without the original code
can only be performed by an authorized dealer.
9
10
Code Systems, Inc. Limited Lifetime Warranty
Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle security
product (the “Product”), purchased from an authorized CODE dealer, that (except as provided below) should this
Product under normal use and conditions, be proven defective in material or workmanship DURING THE LIFETIME OF
THE VEHICLE IN WHICH IT WAS ORIGINALLYINSTALLED, such defect(s) will be repaired or replaced (at CODE’s
option) without charge for parts directly related to repairs of the defect(s).
Switches, indicator lights, and transmitter cases are similarly warranted to the original purchaser for a
period of one (1) year from the date of purchase of the Product.
CODE accessories, sold separately, are covered by the applicable warranty accompanying the accessory.
This warranty is non-transferable, non-assignable and is voided when: (1) the Product is removed from
the vehicle in which it was originally installed; or (2) the vehicle in which the Product was originally installed is trans-
ferred to another party.
This warranty does not apply to any product damaged by accident, physical or electrical abuse, improper
installation, alteration, or use contrary to its intended function, fire, flood, or other natural acts.
In order for the Product to be repaired or replaced under the terms of this warranty, the defective Product
must be returned to an authorized CODE dealer and accompanied by a copy of the retail sales receipt. The date of
purchase and year, make and model of the vehicle in which the Product was originally installed must be clearly indicated
on the sales receipt.
This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED.
ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITYAND FITNESS
FORAPARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. IN
NO CASE SHALL CODE BE LIABLE FORANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH
OF THIS ORANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.
CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF CODE’S
LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE
AND, IN NO EVENT SHALL CODE’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE ORIGINAL
PURCHASER OF THE PRODUCT WITHOUT INSTALLATION LABOR.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which
vary from state to state
11
Code Systems, Inc.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that
may cause undesired operation.
Warning!
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
12
|