Parts Page Reorder No. PD05•21
Effective May, 2005
Supersedes PD05•02
For Serial No. 4G1255 and Higher
Right Angle Mini-Orbital Sander
Air Tool Manual – Safety, Operation and Maintenance
SAVE THIS DOCUMENT, EDUCATE ALL PERSONNEL
Model:
58035 – 15,000 RPM
58037 – 12,000 RPM
58038 – 12,000 RPM
Read and understand this tool manual before operating your air tool. Follow all safety rules for the protection of operating personnel
as well as adjacent areas. Always operate, inspect and maintain this tool in accordance with the American National Safety Institute
(ANSI) Safety Code for Portable Air Tools – B186.1. For additional safety information, refer to – ANSI B7.1, Code of Federal Regulation
– CFR 29 Part 1910, European Committee for Standards (EN) Hand Held Non-Electric Power Tools – Safety Requirements and
applicable State and Local Regulations.
SAFETY LEGEND
WARNING
WARNING
Practice safety requirements. Work alert,
have proper attire, and do not operate tools under
the influence of alcohol or drugs.
Read and understand tool manual before
work starts to reduce risk of injury to
operator, visitors, and tool.
WARNING
Eye protection must be worn at all times,
eye protection to conform to ANSI Z87.1.
WARNING
Ear protection to be worn when exposure to sound,
exceeds the limits of applicable Federal, State or
local statues, ordinances and/or regulations.
WARNING
WARNING
Respiratory protection to be used when exposed to
contaminants that exceed the applicable threshold
limit values required by law.
Air line hazard, pressurized supply lines and flexible
hoses can cause serious injury. Do not use damaged,
frayed or deteriorated air hoses and fittings.
SAFETY INSTRUCTIONS
Carefully Read all instructions before operating or servicing any Dynabrade® Abrasive Power Tool.
Products offered by Dynabrade are not to be modified, converted or otherwise altered from the original design without expressed written
consent from Dynabrade, Inc.
Tool Intent: Right Angle Mini-Orbital Sander is ideal for finesse sanding.
Do Not Use Tool For Anything Other Than Its Intended Applications.
This power tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electrical power.
Training: Proper care, maintenance, and storage of your tool will maximize their performance.
• Employer's Responsibility – Provide Right Angle Mini-Orbital Sander operator with safety instructions and training for safe use of tools and accessories.
Accessory Selection:
• Abrasive/accessory RPM (speed) rating MUST be approved for AT LEAST the tool RPM rating.
• Before mounting an accessory, visually inspect for defects. Do not use defective accessories.
• Use only recommended accessories. See back page of manual and Dynabrade Literature.
• Follow tool specifications before choosing size and type of accessory.
• Only use recommended fittings and air line sizes. Air supply hoses and air hose assemblies must have a minimum working pressure rating of 150 PSIG
(10 Bars, g) or 150 percent of the maximum pressure produced in the system, whichever is higher. (See tool Machine Specifications table.)
Maintenance Instructions
Important: A preventative maintenance program is recommended whenever portable power tools are used. The program should include inspection of air
supply lines, air line pressure, proper lubrication and repair of tools. See Preventative Maintenance Schedule on pg 7.
Refer to ANSI B186.1 for additional maintenance information.
•
•
Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model#, Serial# and RPM of your air tool.
It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due
to unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 11405 Air Filter-Regulator-Lubricator (FRL) – Provides accurate
air pressure regulation and two stage filtration of water contaminants. Operates 40 SCFM @ 100 PSIG with 3/8" NPT female ports.
•
•
Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the
filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.
Lubricate wick system through the angle gear oil fitting with 2-3 plunges for every 24 hours of use, to achieve maximum gear life.
Important: Use only 95848 Gear Oil dispensed with the 95581 Gun. DO NOT contaminate the wick with any other oil or grease product.
Routine Preventative Maintenance:
•
•
Check free speed of Right Angle Mini-Orbital Sander using a tachometer on a regular basis.
Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,
ketones, chlorinated hydrocarbons or nitro carbons.
DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40®).
A Motor Tune-Up Kit (P/N 96179) is available which includes high wear and medium wear motor parts.
All tool labels must be kept legible at all times. User is responsible for maintaining specification information i.e.:
Model #, S/N, and RPM. (See Assembly Breakdown)
•
•
•
•
•
•
Blow air supply hose out prior to initial use.
Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.
Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.
After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to lubricate air motor.
Check for excessive tool vibration.
Handling and Storage:
•
•
•
•
•
Use of tool rests, hangers and/or balancers is recommended.
Protect tool inlet from debris (see Notice below).
DO NOT carry tool by air hose, or near the tool throttle lever.
Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.
Store accessories in protective racks or compartments to prevent damage.
Machine Specifications
Model
Number
Motor
HP (W)
Motor
RPM
Sound
Level
Maximum Air Flow
CFM/SCFM (LPM)
Air Pressure
PSIG (Bars)
Weight
Pound (kg)
Length
Inch (mm)
Height
Inch (mm)
58035
58037
58038
.4 (298)
.4 (298)
.4 (298)
15,000
12,000
12,000
85
85
85
3/21 (595)
3/20 (566)
3/20 (566)
90 (6.2)
90 (6.2)
90 (6.2)
1.63 (.74)
1.63 (.74)
1.63 (.74)
5-7/16 (138)
5-7/16 (138)
5-7/16 (138)
3-11/16 (94)
3-3/4 (96)
4 (104)
Additional Specifications: Air Inlet Thread 1/4" NPT • Hose I.D. Size 1/4" or 8mm
Notice
All Dynabrade motors use the highest quality parts and materials available and are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is
contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of
lubrication during the use of this tool.
OneYear Warranty
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date
of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall
repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our
examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations,
instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to
affect its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
3
Right Angle Mini-Orbital Sander
Complete Assembly
Models:
58035 – 15,000 RPM
58037 – 12,000 RPM
58038 – 12,000 RPM
Index Key
No. Part #
Description
1
54088 Pad - Mdl: 58035
54018 Pad - Mdl: 58037
54031 Pad - Mdl: 58038
33
17 N•m
T
32
W
2
3
4
97175 Screw (4)
1
30
95615 Roloc® Shell
29
30701 Plate - Mdl: 58035, 37
30721 Plate - Mdl: 58038
30709 Boot Clamp
30700 Boot
97174 Screw
30702 Balancer Shaft
30705 Bearing (2)
27
26
25
24
5
6
7
8
9
A
4
39
41
34
31
10 97172 Snap Ring
11 97173 Set Screw
12 30703 Counterweight
13 02035 Lock Ring
14 30704 Shaft
15 01486 Felt Silencer
16 54520 Bearing
17 97118 Shim
23
21
28
A
8
W
1
22
40
34
18 97117 Shim
19 97116 Shim
20
18
38
19
17
20
Gear
O
1
37
02597 Mdl: 58035
02623 Mdl: 58037, 58038
36
35
21 02044 Bottom Wick
22 02045 Top Wick
23 02052 Housing
24 02033 Needle Bearing
25 02041 Gear Oil Plate
26 01040 Gear Oil Fitting
27 01728 Felt Silencer (2)
28 01461 Lock Nut
16
15
23 N•m
T
55
O
1
53
49
51
48
29 01547 Collar
30 Pinion
14
46
47
02598 Mdl: 58035
02624 Mdl: 58037, 58038
A
8
31 02649 Bearing
13
11
23 N•m
T
A
8
32 54529 Shim (3/pkg.)
33 01478 Front Bearing Plate
34 50767 Pin (2)
54
52
12
A
8
50
45
42
35 01479 Spacer
36 02037 Rotor
44
43
10
A
8
37 01480 Blades (4/Pkg.)
38 01476 Cylinder
39 02676 Rear Bearing Plate
40 02696 Bearing
41 02679 Shield
42 01448 Throttle Lever
01462 Safety Lock Lever
9
7
8
Optional Accessory
A
8
43 01449 Valve Stem
44 95558 Retaining Ring
45 12132 Pin
6
A
8
46 30710 Housing - Mdl: 58035
30712 Housing - Mdl: 58037
30713 Housing - Mdl: 58038
95745 Flow Control Assembly (1/4" NPT)
5
2
47 95730 O-Ring
48 01469 Speed Regulator
KEY
4
1
Oil: O1 = Air Lube
O
W
A
Assembly
49 01024 O-Ring
50 01464 Seal
3
Wicking: W1 = Gear Oil
51 01472 Tip Valve
52 01468 Spring
53 96065 O-Ring
54 53190 Block Plate
55 01494 Inlet Bushing
Adhesive: A4 = Loctite #680
A8 = Loctite #567
T
Torque: N•m x 8.85 = In. - lbs.
4
Disassembly/Assembly Instructions - Right Angle Tools
Important: Manufacturer’s warranty is void if tool is disassembled before warranty expires.
Please refer to parts breakdown for part identification.
Motor Disassembly:
1. Shut the air supply and disconnect the sander from the air supply hose. Important: Hold the air inlet adapter securely with a wrench before removing the air fitting so as
to prevent damage to the composite housing.
2. Secure the motor housing in a vise by using the 52296 Repair Collar to provide protection for the housing. Position the tool so that the angle head is pointing up.
3. Use a 34mm or an adjustable wrench to remove the 01461 Lock Nut by turning it clockwise.
4. Pull the motor assembly out of the motor housing.
5. Fasten the 96346, 2" Bearing Separator around the portion of the 01476 Cylinder that is closest to the 02676 Rear Bearing Plate.
6. Place the bearing separator on the table of the arbor press so that the pinion gear end of the rotor is pointing toward the floor.
7. Use a 3/16" dia. flat end drive punch as a press tool and position it on the rotor shaft. Press the rotor out of the 02696 Bearing. The 02696 Bearing can be removed from the
02676 Bearing Plate with the 96210 Bearing Removal Tool and the 96232 Arbor Press (#2).
8. Secure the body of the rotor in a vise with bronze or aluminum jaws so that the pinion gear is pointing up.
9. Use a wrench to remove the pinion gear from the rotor by turning it counterclockwise.
10. Pull the 01478 Front Bearing Plate with bearing off the rotor.
11. Push the 02649 Bearing out of the front bearing plate and remove the shims.
12. Slip the 01479 Spacer off the rotor.
Motor Disassembly Complete.
Orbital Head Disassembly:
1. Shut the air supply and disconnect the sander from the air supply hose.
2. Remove the pad.
3. Use a Phillips® screwdriver to remove the 97175 Screws (4).
4. Use a sharp utility knife to cut through and remove the 30709 Boot Clamp. Important: Cut the clamp carefully so as to prevent personal injury and damage
to the 30700 Boot.
5. Pull the 30700 Boot from the 02052 Housing.
6. Hold the 30703 Counterweight stationary with a 19mm open-end wrench. Use a Phillips® screwdriver to loosen the 97174 Screw and remove the 30702 Balancer Shaft.
7. Use a 5/64" (2mm) slotted screw, screwdriver to remove the 97172 Snap Ring.
8. Use the 96210 Bearing Removal Tool and the 96232 Arbor Press (#2) to push the 30705 Bearings (2) out of the balancer shaft.
9. Use a 2mm Hex Key to remove the 97173 Set Screw and the 30703 Counterweight.
Orbital Head Disassembly Complete.
Right Angle Housing Disassembly:
1. Shut the air supply and disconnect the sander from the air supply hose.
2. Secure the 30710 / 30712 Housing in a vise by using the 52296 Repair Collar to provide protection for the housing. Position the housing so that the 02035 Lock
Ring is facing up.
3. Use the 50971 Lock Ring Tool to remove the 02035 Lock Ring, by turning it counterclockwise.
4. Grasp the shaft to pull the shaft, the 54520 Bearing, the gear and the shims out of the housing.
5. The bearing and gear can be pressed off the spindle with the 96232, Arbor Press (#2).
6. If necessary the 02033 Needle Bearing can be removed by using a 5/16" dia. flat end drive punch to push the 02041 Gear Oil Plate, and 01041 Gear Oil Fitting out
of the 02052 Housing.
Right Angle Housing Disassembly Complete.
Valve Disassembly:
1. Use the 52296 Repair Collar to securely hold the motor housing in a vise so that the inlet adapter is pointing up.
2. Remove the valve components by loosening the inlet adapter. Remove the 01468 Spring, 01472 Tip Valve, and 01464 Seal.
3. Reposition the motor housing in the vise so that the throttle lever, and the 12132 Pin are accessible. Remove the pin and lever by using a 2.5mm dia. drive punch.
4. Use retaining ring pliers to remove the 95558 Retaining Ring and push the 01469 Speed Regulator Assembly out of the motor housing.
Valve Disassembly Complete.
Important: Clean and inspect parts for wear or damage before assembling.
Valve Assembly:
1. Install the 01469 Speed Regulator Assembly into the motor housing, and secure it in place with the 95558 Retaining Ring.
2. Use the 52296 Repair Collar to securely hold the motor housing in a vise so that the air inlet is pointing up.
3. Insert the 01449 Valve Stem into the speed regulator assembly so that the hole in the valve stem aligns with the air inlet hole in the motor housing.
4. Install the 01464 Seal so that it lays flat. Use a needle nose pliers to grasp the nylon portion of the 01472 Tip Valve and install it so that the metal pin fits into the hole
of the 01449 Valve Stem.
5. Install the 01468 Spring so that the smaller end fits against the back of the tip valve.
6. Refer to the parts breakdown for part identification and the sequence of assembly. Apply a small amount of Loctite® #567 (or equivalent) to the male threads of the
inlet adapter and tighten the inlet adapter. (Torque to 23 N-m/200 in. lbs.)
Valve Body Assembly Complete.
Motor Assembly:
1. Secure the body of the rotor in a vise with bronze or aluminum jaws so that the threaded end is pointing up.
2. Slip the 01479 Spacer onto the 02037 Rotor.
3. Select .003 (.08mm) thick shims from the 54529 Shim Pack and place these into the 01478 Front Bearing Plate.
4. Install the 02649 Bearing into the front bearing plate and slip the bearing/plate assembly onto the rotor.
5. Install the pinion onto the rotor, making it hand tight.
(continued on next page)
5
Disassembly/Assembly Instructions - Right Angle Tools
6. Check the clearance between the rotor and the bearing plate with a .001 thick feeler gauge. Clearance should be .001” to .0015” (0.03-0.04mm). If it’s necessary, readjust
clearance by repeating steps 3-5 with different thickness shims.
7. Once the proper rotor/plate clearance is achieved wrench tighten the pinion. (Torque to 17N·m/150 in. lbs.)
8. Apply the 95842 Dynabrade Air Lube (10W/NR or equivalent) to the 01480 Blades and install them onto the rotor.
9. Use the 96216 Bearing Press Tool so that it pushes against the outer race of the 02696 Bearing and install it into the 02676 Rear Bearing Plate with the arbor press.
10. Place the pinion on the tool plate of the arbor press so that the rear portion of the rotor is pointing up.
11. Install the 01476 Cylinder so that it rests against the 01478 Bearing Plate. Note: Make sure that the air inlet passage of the cylinder will properly aligned with the air inlet
passage in the 02676 Bearing Plate.
12. Use the 96216 Bearing Press Tool so that it pushes against the inner race of the 02696 Bearing and install the rear bearing/plate assembly onto the rotor with the
arbor press. Important: Carefully press the rear bearing/plate assembly onto the rotor until it touches the 01476 Cylinder. A “snug” fit should exist between the bearing
plates and cylinder. If it is too tight the rotor will not turn freely and will cause damage to the bearings. If it is too loose the proper bearing preload will not be achieved.
13. Apply a small amount of grease to the seal of the 02696 Rear Bearing and place the 02679 Shield against the seal of the bearing.
14. Install the motor assembly into the housing so that the air passage node of the rear bearing plate aligns with the air passage notch inside the housing.
15. Apply a small amount of Loctite® #567 (or equivalent) to the threads of the motor housing and use a 34mm (or an adjustable wrench) to connect the angle head assembly
to the motor housing. (Torque to 34 N-m/300 in. lbs.)
Motor Assembly Complete.
Right Angle Housing Assembly:
1. Press the 01041 Gear Oil Fitting into the 02041 Gear Oil Plate.
2. Carefully apply two drops of Loctite® #680 (or equivalent) to the recessed area of the
02052 Housing
02033 Needle Bearing
02052 Housing and press the gear oil plate along with gear oil fitting into the housing.
(Allow 30 minutes for the adhesive to cure.)
3. Press the 02033 Needle Bearing into the housing.
02041 Gear Oil Plate
01040 Gear Oil Fitting
4. Position the 96239 Bearing Press Tool so that it rests against the inner race of the
54520 Bearing and press the bearing onto the spindle.
5. Align the hex shaped I.D. area of the gear with that of the spindle and press the gear into place.
6. Apply a small amount of Loctite® #567 (or equivalent) to the mating threads of the 02052
Housing. Connect these parts while being aware of the right and left hand threads.
2 Drops of Loctite
7. Place the 52296 Repair Collar around the motor housing and position the tool in a vise so
that the angle housing end of the tool is pointing up.
8. Use a 34mm or adjustable wrench on the 01461 Lock Nut while holding the angle housing
stationary with one hand. Note: The throttle lever can be positioned in 360˚ to the desired location.
Allow for additional rotation when tightening the lock nut. (Torque to 34 N-m/300 in. lbs.)
9. Reposition the tool assembly in the vise so that the opening in the angle housing, for the 02035 Lock Ring is facing up.
10. Soak the wicks in the 95848 Gear Oil before installing them into the 02052 Housing. Install the top wick first followed by the bottom wick. Position truncated side of each
wick toward the end of the pinion gear.
11. Install the 30704 Shaft into the angle housing. Apply a slight amount of pressure down on the spindle while rotating it back and forth checking for the proper backlash or fit
between the gears. A slight amount of backlash or clearance should exist between the bevel and pinion gears. When a tight fit exist, then add shims as needed placing the
required thickness of shims between the outer race of the 54520 Bearing and the bearing seat in the housing.
12. Place (1) 01486 Felt Silencer into the 02035 Lock Ring, and apply a small amount of Loctite® #567 (or equivalent) to the threads of the 02035 Lock Ring. Use the
50971 Lock Ring Wrench to install the lock ring onto the 02052 Housing. (Torque to 23 N-m/200 in. lbs.)
Right Angle Housing Assembly Complete.
Orbital Head Assembly:
1. Install the 30703 Counterweight onto the 30704 Shaft, aligning the screw hole with the pilot hole in the shaft.
2. Apply a small amount of the Loctite® #567 (or equivalent) to the threads of the 97173 Set Screw.
3. Use a 2mm hex key to install the 97173 Set Screw into the 30703 Counterweight and secure the counterweight to the 30704 Shaft.
4. Use the raised outer diameter of the 96216 Bearing Press Tool and the 96232 Arbor Press (#2) to press the 30705 Bearings (2) into the 30702 Balancer Shaft.
5. Install the 97172 Snap Ring into the 30702 Balancer Shaft.
6. Install the balancer shaft assembly onto the 30704 Shaft.
7. Apply a small amount of the Loctite® #567 (or equivalent) onto the threads of the 97174 Screw. Hold the 30703 Counterweight stationary with a 19mm open-end wrench.
Use a Phillips® screwdriver to tighten the 97174 Screw into the 30704 Shaft.
8. Install the 30700 Boot and the 30701 Plate, aligning the screw holes.
9. Install the 97175 Screws (4) securely.
10. Install the 30709 Boot Clamp around the 30700 Boot and use a HEAT GUN to shrink-fit the clamp, securing the boot to the 02052 Housing.
11. Install the pad.
Orbital Head Assembly Complete.
Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed. Operate tool for 30 seconds to determine if tool
is operating properly and to allow lubricating oils to properly penetrate motor. Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or
operates at a higher RPM than marked on the tool, the tool should be serviced to correct the cause before use.
Loctite® is a registered trademark of Loctite Corp.
6
Preventative Maintenance Schedule
For All Right Angle Mini-Orbital Sander
This service chart is published as a guide to expectant life of component parts. The replacement levels are based on average tool
usage over one year. Dynabrade Inc. considers one year usage to be 1,000 hours.
Parts Common to all Models:
Index Part
Number
Description
Number High Wear Medium Wear Low Wear Non-Wear
LEGEND
#
Required
100%
70%
30%
10%
T
X
Included in Tune-up Kit
Type of wear, no other
comments apply.
1
2
3
See Note Pads
97175 Screw
30701 Plate
1
4
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
X
X
X
X
L
Easily lost. Care during
assembly/disassembly.
4
5
30709 Boot Clamp
30700 Boot
6
7
8
9
10
11
12
13
14
15
16
17
18
97174 Screw
X
X
D
R
Easily damaged during
assembly/disassembly.
30702 Balancer Shaft
30705 Bearing
97172 Snap Ring
97173 Set Screw
30703 Counterweight
02035 Lock Ring
30704 Shaft
01486 Felt Silencer
54520 Bearing
97118 Shim
X
L
X
Replace each time tool is
disassembled.
X
X
X
T
T
T
T
T
97117 Shim
97116 Shim
19 See Note Gear
X
20
21
02044 Bottom Wick
02045 Top Wick
T
T
22 See Note Housing
X
23
24
25
26
27
28
02033 Needle Bearing
X
X
X
02041 Gear Oil Plate
01040 Gear Oil Fitting
01728 Felt Silencer
01461 Lock Nut
96179 – Motor Tune-Up Kit
T
X
X
X
01547 Collar
29 See Note Pinion
30
31
32
33
34
35
36
37
38
39
40
41
02649 Bearing
T
T
54529 Shim (3/pkg.)
01478 Front Bearing Plate
50767 Pin
01479 Spacer
02037 Rotor
01480 Blades (4/Pkg.)
01476 Cylinder
02676 Rear Bearing Plate
02696 Bearing
X
X
X
X
T
X
X
T
T
02679 Shield
01448 Throttle Lever
01462 Safety Lock Lever
01449 Valve Stem
95558 Retaining Ring
12132 Pin
X
X
42
43
44
T
T
T
45 See Note Housing
X
46
47
48
49
50
51
52
53
53
95730 O-Ring
01469 Speed Regulator Assy.
01024 O-Ring
01464 Seal
01472 Tip Valve
01468 Spring
96065 O-Ring
53190 Block Plate
01494 Inlet Bushing
T
T
T
T
T
T
T
X
X
Note: Pads are a consumable item. They are application sensitive. Their expectant life will vary depending on the
specific work application and work habit of the operator.
7
Optional Accessories
96179 Motor Tune-Up Kit
52296 Repair Collar
•
Includes assorted parts to help
maintain and repair motor.
•
Specially designed collar for use in vise to prevent
damage to valve body of tool during disassembly/assembly.
Dynabrade Angle Gear Oil
•
Specifically formulated to saturate wick system in right
angle gear head.
Dynaswivel®
•
Easy to apply using Dynabrade P/N 95541 Oil Gun.
Apply 3 plunges every 8 hours of operation into tools
lubrication fitting.
•
Swivels 360° at two locations which allows an
air hose to drop straight to the floor, no matter
how the tool is held.
95848: 2 oz. tube
95849: 10 oz. tube
94300 1/4" NPT.
Dynabrade Air Lube
Special Repair Tools
Note: Mentioned In Assembly/Disassembly
•
•
•
•
Formulated for pneumatic equipment.
Absorbs up to 10% of its weight in water.
Prevents rust and formation of sludge.
96216 Bearing Press Tool
96232 (#2) Arbor Press
96346 (2") Bearing Separator
96210 Bearing Removal Tool
96239 Bearing Press Tool
52296 Repair Collar
Keeps pneumatic tools operating longer
with greater power and less down time.
95842: 1pt. (473 ml)
95843: 1gal. (3.8L)
50971 Lock Ring Tool
Special Greasing Instructions
Lubricate wick system through the angle gear oil fitting with 2-3 plunges for every 24
hours of use, to achieve maximum gear life.
Apply 3 plunges
into lubrication
fitting every
24 hours of
Expect a
Important: Use only the recommended angle gear oil for the wick system.
Do not contaminate the wick with any other oil or grease product.
gear life of
500 hours
minimum,
with proper
lubrication.
operation.
(Order 95848 Gear Oil and 95541 Gun)
02052 Housing
01040 Gear Oil Fitting
Reference Contact Information
1. American National Safety Institute – ANSI
3. European Committee for Standardization
Rue de Stassart 36
25 West 43rd Street
Forth Floor
B - 1050 Brussels, Belgium
New York, NY 10036
Tel: 1 (212) 642-4900
Fax: 1 (212) 398-0023
2. Government Printing Office – GPO
Superintendent of Documents
Attn. New Orders
P.O. Box 371954
Pittsburgh, PA 15250-7954
Tel: 1 (202) 512-1803
Visit Our Web Site: www.dynabrade.com
Email: [email protected]
Phone: (716) 631-0100 Fax: 716-631-2073
DYNABRADE®
DYNABRADE, INC., 8989 Sheridan Drive
•
Clarence, NY 14031-1490
•
•
•
International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
Zone Artisanale
•
L-5485 Wormeldange—Haut, Luxembourg
•
Telephone: 352 76 84 94 1
•
Fax: 352 76 84 95 1
©DYNABRADE, INC., 2005
PRINTED IN USA
PD05.02_01/05
|